Farmer DiamondsUsed hard drives with statutory warranty – home page

Guides

Measured values of a used hard drive: what each figure means

Every drive page carries the same details. Here is what each of them means – and how to read it in our shop.

Power-on hours

The hours the drive has been switched on so far – the most important clue to how it has been used. One year of continuous operation is 8,766 hours. We name no hour count from which a hard drive would be “too old”; more under Power-on hours: how many is a lot?

How we state itAs the row “Power-on hours” on every drive page, in hours and converted to years below. Power-on hours move the price; the lists can be sorted and filtered by them.

Power cycles

The number of power cycles: how often the drive was started. It complements the power-on hours. Few power cycles over many hours mean the drive ran for long stretches; many power cycles over few hours mean it was switched on and off often.

How we state itAs the row “Power cycles” on every drive page and as a column in the lists. Power cycles do not affect the price.

Bad sectors

A sector is the smallest unit in which a hard drive stores data. The drive itself keeps count of how many of its sectors it has found defective; we read that number out. A measured zero is not the same as a missing value: “0” means measured with no findings, “not recorded” means the value was not read.

How we state itAs the row “Bad sectors” with the measured number or with “not recorded”. Measured bad sectors lower the price, and so does a value that was not recorded.

Self-test

A test run the drive carries out itself. It comes in two lengths: the short self-test reads only a small part of the surface, the long one reads the whole surface.

  • long · passed long self-test over the whole surface, no findings
  • short · passed short self-test, no findings
  • not recorded no current self-test – we show no value we do not have

How we state itAs the row “Self-test” with the kind of test and its result; in the lists as a tinted label with the same words. A passed long self-test raises the price. Where there is no self-test, it says “not recorded”.

Not recorded

Where a value says “not recorded”, we did not measure it for this drive. We then write neither a zero nor an estimate: a zero would be a measurement that does not exist.

How we state itAs the words “not recorded” in place of the value – for power-on hours, power cycles, bad sectors and the self-test. A drive without recorded power-on hours comes last when sorted by hours; a filter on the hours leaves it out.

Capacity

Capacity is given in terabytes (TB), as on the label of the drive. Operating systems count in tebibytes (TiB) and therefore show a smaller number for the same amount of storage. Nothing is missing; the arithmetic is under TB and TiB.

An example from what we offer: a drive labelled 20 TB reports 18.19 TiB to the operating system.

How we state itAs the row “Capacity” in TB and below it the figure in TiB the operating system reports – on every drive page.

Interface

The connection through which the drive is attached to the computer. It decides whether the drive fits your system.

For the drives currently on offer it reads: SATA III (6 Gb/s).

For the models it applies to, it also says: “Compatible with standard desktop PCs: regular SATA data and power connectors.”

How we state itAs the row “Interface” on every drive page and at the top of the model page.

Condition

The condition says whether a drive is used or factory-recertified. “factory-recertified (refurbished)” is only stated for drives the maker overhauled and certified again – and that per drive, not for a model as a whole.

What the words mean in detail is under Used, refurbished, factory-recertified.

How we state itAs the row “Condition” on every drive page: “used” or “factory-recertified (refurbished)”. The search over all hard drives can be filtered by condition.

Use: NAS, RAID, 24/7 operation

Whether a model is suitable for a NAS, a RAID or 24/7 operation is something we settle per model – not per drive. Where a model is not suitable for it, we say so explicitly.

From suitable models we put together ready-made sets for RAID and ZFS.

How we state itFor a model that is not suitable for it, its page and every one of its drives say: “Not suitable for NAS, 24/7 operation or RAID.” There is no RAID or ZFS set of such a model.

Item number

Every drive has its own item number. Under it you find exactly this drive again – in the shop and in your order. The item number is not the serial number of the drive.

How we state itAs “Item no.: FD-…” above the measured values of every drive, in the lists and in the address of its page.

Test report

Every drive has its own test report.

How we state itYou receive the test report after payment, by e-mail with the shipping confirmation. The serial number is on no public page of the shop; after dispatch it is on your order page, on the invoice and on the delivery note.

Data erasure

What happened to the previous data of a drive is stated on its page under “What happened to the previous data”. It carries one of two statements. Where a completed full overwrite is on record for the drive, it reads:

Completely overwritten with ATA SANITIZE (OVERWRITE EXT) – a full overwrite per NIST 800-88 “Purge”.

It is not a cryptographic erasure.

Otherwise it reads: “Erasure: not documented”.

How we state itWhat counts is always the statement on the page of the individual drive.